1/8" Two-Piece Launch Rod

Ideal replacement rod and alignment tool. This 1/8 inch (3.2 mm) diameter launch rod is ideal for most standard engine powered rockets. It attaches to the launch pad then you can align the launch lugs on your Estes rocket to the launch rod and slide it down. As the rocket launches, it quickly gains enough speed to fly with stability, thanks to the launch rod, and then flies into the air. Fits the 2215 Porta-Pad II Also works great when used as an alignment tool on model rockets that req…

24" Estes Nylon Parachute

Strong and durable to safely recover larger-sized rockets Bright red for great visibility Comes preassembled A fully assembled 24 in. (61 cm) nylon parachute is intended for larger-sized model rockets where the strength of the recovery system is paramount. Made of high-quality red nylon cloth, this chute features stitched braided nylon shrouds for reliable rocket recovery and lasts longer than an entry-level plastic shoot.

24mm to 29mm Motor Adapter Set (2 pk)

Very simple transformation of an Estes 24 mm casing into an Estes 29 mm casing size. Reusable. Adapts Estes 24 mm C11/D, Estes 24 mm E and Estes E30 series Composite engines to a 29 mm Estes casing size. Also adapts other brands of 24 mm composite single use and RMS motor systems. 2 sets per package. Includes orange paper adapter tubes, as shown, and are designed for reuse over and over.

3/16" Two-Piece Maxi Rod

Launch rod with extra strength and length for larger rockets. Going big? You might need a stronger launch rod, like this 3/16 diameter rod built for heavier rockets and higher power motors. It attaches to the launch pad, and your Estes rocket simply slides over the rod using the launch lugs attached to the rocket. As the rocket launches, it quickly gains enough speed to fly with stability, and then leaves the launch rod. That requires roughly 30mph, and this length is perfect to accelerate…

30" Estes Nylon Parachute

Strong and durable to safely recover larger-sized rockets Bright red for great visibility Comes preassembled A fully assembled 30 in. (76 cm) nylon parachute intended for larger model rockets where strength of the recovery system is paramount. Made of high-quality red nylon cloth, this chute also features stitched braided nylon shrouds for reliable rocket recovery.

AltiTrak Altitude Tracker

How high did it really go? Next time, measure it with this easy to use device. Pull the trigger, follow the rocket in the sights to apogee, then release the trigger to lock the reading. It is that easy. No need for hundreds of dollars of altimeters! The Estes Altitrack was designed for educational uses, but is perfect for any application of rapid design. Track the altitude of your rocket without reducing the height by adding mass. Two AltiTraks can give you much greater accuracy. Perfect f…

C11, D & E Engine Model Rocket Display

Model Rocket Display stand for all of your C11, D & E engine size model rockets! 3 to a pack. What a great value! Display your rockets in style! Available in mini, standard and C11, D & E engine mount sizes.

E Launch Controller

2230 E Launch Controller is a must when launching “E” engine powered rockets but can be used to launch all Estes engines. Upgrade the capacity of your launch controller with the “E”. This launch controller enables you to launch the E Estes motors, but can launch any Estes Engine. This controller includes a safety switch, continuity check, and that good ole’ button called “Launch”. It comes complete with safety key and 30 ft. of cable. Requires 4 “AA” alkaline batteries, n…

Electron Beam Launch Controller

INSTRUCTIONS Get ready to launch your new rocket with the reliable Electron Beam® Launch Controller. The Launch Controller comes fully assembled with 17 ft (5.2 m) of cable and requires 4 new 1.5V ‘AA’ alkaline batteries – sold separately. A GREAT Controller for launching all mini, standard (A-C) and D powered rockets.

Estes Blast Deflector Plate

New blast deflector plate replaces that old worn out one!

Fin Alignment Guide

FAST & ACCURATE fin alignment Great for three or four finned rockets Fits body tubes ranging from BT-20 to BT-80 A precision molded accessory that makes it easy to glue three or four fins to various sized body tubes ranging from BT-20 to BT-80 diameters. Unique and adjustable vertical fin holders can accommodate either 3/32 in. or 1/8 in. balsa, bass or plywood fins. This is a must-have tool for any serious model rocket builder. Never attach your fins wrong again and remove that pa…

Mini AltiTrak Altitude Trackers (3pk)

Take learning to new heights with this low-cost technology solution for tracking model rocket altitude. These small, easy to transport altitude tracking devices allow for students to track flight data, analyze and graph! Coming in a 3 pack, this makes it easier on your wallet so you can provide engaging learning opportunities for your students. Need a savior from a boring classroom, but want to keep it educational? Introduce the Mini AltiTrak to your rocketry activity to engage students in th…

Mini Engine Model Rocket Display Stand

Model Rocket Display stand for all of your mini engine size model rockets! 3 to a pack. What a great value!

Mini to Standard Engine Adapter

Two simple steps transform a mini engine into a standard size. Insert a mini engine into the adapter, and insert the adapter into a rocket. 3 adapters per pack. Reusable. Adapts standard engine mounts to hold a mini engine. NOTE:  Rockets weighing up to 2 ounces that would normally fly on A8-3 engines can be flown on A10-3T engines.

Model Rocket Cradle

Multiple ways to use. Great for assembly or display! Just like in real rocketry, rocket cradles are used during construction, storage and transportation of rockets. Use your rocket cradle to hold your rocket on its side while you work to keep the rocket from resting on its fins. It’s perfect for making fin fillets or applying decals. It’s one of the handiest pieces of equipment to have when building your models! You can even in the field when you’re prepping larger rockets for flight. …

Porta Pad II Launch Pad

Quick Assembly. Requires no glue or tools. Not Included – 2220 Electron Beam Launch Controller Comes complete with blast deflector, standoff stem, two-piece 1/8 in. launch rod and launch rod cap. Launch direction may be adjusted 30 degrees from vertical and can accommodate a 3/16 in (5 mm) Maxi Launch Rod - sold separately. Minor assembly required and no glue or tools are needed. Can be used to launch rockets powered with all mini, standard (A-C) and D engines.

Porta Pad II Launch Pad & Controller

A GREAT combo! A GREAT price! Launch Pad and Launch Controller included! The Launch Pad comes complete with blast deflector, standoff stem, two-piece 1/8 in. launch rod and launch rod cap. Launch direction may be adjusted 30 degrees from vertical and can accommodate a 3/16 in (5 mm) Maxi Launch Rod - sold separately. Minor assembly required and no glue or tools are needed. The Launch Controller comes fully assembled with 17 ft (5.2 m) of cable and requires 4 new 1.5V 'AA' alkaline batterie…

Porta-Pad E Launch Pad

Porta-Pad E launch pad requires no glue or tools. Quick assembly and includes 1/4 in. (6 mm) launch rod! The “E” launch pad sports a beefier blast deflector and stand to handle those “E” powered engines. The more durable design lends to a longer life expectancy and enables you to launch any of the Estes model rocket engines. This pairs perfectly with the “E” launch controller. Quick assembly. Includes a 1/4 in. (6 mm) launch rod, but can accommodate a 3/16 in. (5 mm) Maxi…

Pro Series II Launch Controller

INSTRUCTIONS Great for launching single and two-cluster engine powered rockets Comes fully assembled The Pro Series II Launch Controller is the ultimate launch controller for any single or clustered rocket! Powered by six, ‘C’ size alkaline batteries (not included), this launch controller provides plenty of energy to your single or two engine cluster rockets. The Pro Series II Launch Controller also features an alternative power source option for launching up to 10 rocke…

Pro Series II Launch Pad

Launch all your Pro Series II rockets Compatible with most mid-powered rockets Easy to assemble and transport The finest launch base to hit the market! Big and sturdy and made with removable PVC tube legs, it also includes a two-piece, threaded 1/4 in. x 60 in. steel launch rod and 5 in. galvanized blast deflector plate. This is the perfect launch base for launching most rocket you have.

Pro Series II Recovery Wadding

Flame resistant recovery wadding necessary for protecting your recovery system Enough wadding for 10-12 Pro Series II launches Can be used with any of our rockets This extra-large bag of flame-resistant recovery wadding contains approximately 216 squares of wadding and is an excellent value for launching and recovery of all sizes of model rockets!

Pro Series II Shock Cord Accessory Pack

Heavy duty elastic shock cords Works on all BIG rockets! Pack of three   This accessory pack contains 3, 1/2 in. x 96 in. heavy duty elastic shock cords for shock your next big rocket design or as a replacement.

Shock Cords & Mount Pack

Contains two sizes of shock cords with mounts and instructions. Contains two 1/8 in. x 18 in and one 1/4 in x 36 in. rubber shock cords and four shock cord mounts.

Standard Engine Model Rocket Display

Model Rocket Display stand for all of your standard engine size model rockets! 3 to a pack. What a great value! Display your rockets in style! Available in mini, standard and C11, D and E engine mount sizes.

Standard to D Engine Adapter

Two simple steps transform a standard engine into a D size. Insert a standard engine into the adapter, and insert the adapter into a rocket. 3 adapters per pack. Reusable. Adapts D engine mounts to hold a standard engine. NOTE:  This motor adapter has been tested in products that use ESTES metal engine hooks. It may not work with other brands of engine hooks. Rockets weighing up to 4 ounces that would normally fly on C11 or D12 engines can be flown on B and C engines.

Tube Cutting Guides (5pc)

A quick and easy way to cut all of the most common sized body tubes to custom lengths! Heavy duty plastic guides slip easily onto your body and allows for precision cuts for specific lengths. 5 guide sets are included. BT5, BT20, BT50, BT55 and BT60. A must have for all rocket builders! You won't find an easier way to shorten that body tube!