Adhesives

Adhesives
  • CA Extra Thick 1/2 oz Pink

    CA Extra Thick 1/2 oz Pink

    Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE™ bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface …

    $4.79

    Stock Level: 9

    $4.79

    Stock Level: 9
  • CA Gap Filling 1/2 oz Purple

    CA Gap Filling 1/2 oz Purple

    Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then as…

    $4.79

    Stock Level: 9

    $4.79

    Stock Level: 9
  • CA Gap Foam Safe 1/2 oz Gold

    CA Gap Foam Safe 1/2 oz Gold

    SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and Insta-Cure+. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clea…

    $9.99

    Stock Level: 11

    $9.99

    Stock Level: 11
  • CA IC-Gel 20g

    CA IC-Gel 20g

    IC-GEL™ is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE™. IC-GEL™, however, can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult with anything other than a full standard CA bottle. IC-GEL™ can b…

    $7.99

    Stock Level: 12

    $7.99

    Stock Level: 12
  • CA Insta-Set 2 oz

    CA Insta-Set 2 oz

    INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA…

    $6.99

    Stock Level: 12

    $6.99

    Stock Level: 12
  • CA Super Thin 1/2 oz Blue

    CA Super Thin 1/2 oz Blue

    Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.

    $4.79

    Stock Level: 11

    $4.79

    Stock Level: 11
  • CA Un-Cure 1oz Green

    CA Un-Cure 1oz Green

    UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics pa…

    $4.99

    Stock Level: 3

    $4.99

    Stock Level: 3
  • Epoxy 15min-13 oz

    Epoxy 15min-13 oz

    MID-CURE™ 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE™ in most applications. MID-CURE™ is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.

    $29.99

    Stock Level: 11

    $29.99

    Stock Level: 11
  • Epoxy 15min-4.5 oz

    Epoxy 15min-4.5 oz

    MID-CURE™ 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE™ in most applications. MID-CURE™ is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.

    $13.99

    Stock Level: 10

    $13.99

    Stock Level: 10
  • Epoxy 15min-9 oz

    Epoxy 15min-9 oz

    MID-CURE™ 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE™ in most applications. MID-CURE™ is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.

    $22.99

    Stock Level: 11

    $22.99

    Stock Level: 11
  • Epoxy 30min-13oz

    Epoxy 30min-13oz

    SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ and FINISH-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full …

    $29.99

    Stock Level: 28

    $29.99

    Stock Level: 28
  • Epoxy 30min-4.5oz

    Epoxy 30min-4.5oz

    SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ and FINISH-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full …

    $13.99

    Stock Level: 34

    $13.99

    Stock Level: 34
  • Epoxy 30min-9oz

    Epoxy 30min-9oz

    SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ and FINISH-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full …

    $22.99

    Stock Level: 33

    $22.99

    Stock Level: 33
  • Epoxy 5min-13oz

    Epoxy 5min-13oz

    QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn’t be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE™ is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CU…

    $29.99

    Stock Level: 30

    $29.99

    Stock Level: 30
  • Epoxy 5min-4.5oz

    Epoxy 5min-4.5oz

    QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn’t be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE™ is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CU…

    $13.99

    Stock Level: 30

    $13.99

    Stock Level: 30
  • Epoxy 5min-9oz

    Epoxy 5min-9oz

    QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn’t be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE™ is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CU…

    $22.99

    Stock Level: 34

    $22.99

    Stock Level: 34
  • Gorilla Glue 2oz

    Gorilla Glue 2oz

    The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. The water activated polyurethane formula expands into materials to form an incredibly strong bond to virtually anything making Gorilla Glue your solution for almost any project or repair. 2 ounce bottle.

    $10.00

    Stock Level: 15

    $10.00

    Stock Level: 15
180
Loading
(Required)
This field is required.
Top

e-Commerce by Rocket Power